50 ft. Black RG11 Low-Loss Coax (F Male to F Male) | 951150

email me this page
Email me this page

Works on every network, on any carrier.

Product Description

The Wilson RG11 75 Ohm black coax cable is 13/32" in diameter with both ends terminated with an F-Male connector. This cable has around 1-2dB of additional loss per 100 feet of cable.  Also, 75-Ohm cable does not handle as much cellular traffic as 50-Ohm so in high user situations, you can see a reduction in data speeds. This low-loss foam cable can be used both indoors and outdoors with connections between amplifiers and antennas, taps, splitters and lightning surge protectors.

Coaxial (or coax) cables are an integral aspect of cell signal booster installation. Cables run from outdoor antennas (donor antennas) to amplifiers, and then connect to the indoor antennas (broadcast antennas) to distribute the boosted signal.

Connectors join the cables using male to female adapters. Connectors link cables between signal meters and outside antennas, and come in handy whether making cell signal readings or installing a new system. For parts and accessories like this, you can count on WilsonPro. 

FAQs

“What can the maximum cable lengths be?”

In general, WilsonPro recommends keeping the cable lengths at or under 100 feet total from amplifier to any antenna.  Ultimately though, this depends on the signal strength outside, loss in type of cable being used, loss through splitters and/or taps, and how much coverage you are trying to achieve.  With a good outside signal, higher quality cables, and higher-grade amplifiers, there are plenty of ways to be able to have longer cable runs.  For example, if you have a strong outside signal of -45dB, you can consider a cable run of around 150 feet from donor to amplifier and still have plenty of signal for the amplifier to work with.

“How do I terminate RG-11 cable?”

You’ll need an RG-11 stripping tool and an RG-11 crimper to get the job done right. Some dikes or a cutting tool are also a handy tool to have around for the job.

First take the RG-11 stripping tool and line it up with the edge of your cable. Spin the tool around the cable several times. You’ll feel the stripper cut through the shielding as you spin it around the cable. Pull the stripping tool off and remove any remaining pieces that remain. You’ll be left with something like this.

Peel the braided metal shielding back so it looks like this. Make sure that no metal shielding makes contact with the center pin. Then slip the RG-11 connector onto the cable. Be sure that the pin from the cable is properly inserted into the pin already in the connector.  If the pin is too long, trim from the cable pin and try again until it fits properly. Do not trim the pin of the connector.

Place the connector and cable into the RG-11 crimper and crimp down firmly, bouncing the crimper a few times to ensure you’ve got a solid crimp.

That’s it! Now just measure out your cable to the proper length and repeat the process on the opposite end.

Warning

Warning: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Specs

Model Number:951150
Price$ 74.99

Review Snapshot

5
(1)

Ratings Distribution

  • 1 Star: 0
  • 2 Stars: 0
  • 3 Stars: 0
  • 4 Stars: 0
  • 5 Stars: 1

5

Increased signal from standard cable

We had low signal due to being in a remote area in the mountains. Tried this cable and it increased the signal quality improving performance.

Bottom Line Yes, I would recommend to a friend

Was this review helpful to you? Yes: 0 No: 0

Submitted a year ago

By Pax

From Duck Creek Village

Q&A

Showing 10 out of 1 Questions

Asked by WarrenP 3 years ago

Question: Does this work with the eqo booster?

Answer: Thank you for reaching out to us! The RG-6 cabling is not recommended for the Eqo booster as the connections on the booster are SMA. We recommend reaching out to us directly for assistance. You can reach us here: http://support.weboost.com/hc/en-us/requests/new Or by phone at 866-294-1660.

Was this question helpful to you? Yes: 0 No: 0


BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider.

Warning.

E911 location information may not be provided or may be inaccurate for calls served by using this device. Please note, the four largest carriers, namely, AT&T, T-Mobile, Verizon and Sprint, and more than 90 regional carriers have given a blanket consent to all boosters meeting the new certification standards